©Eastman Kodak Company, 2009
AS-2652
KODAK AEROCOLOR IV Negative Film 2460
KODAK AEROCOLOR IV Negative Film 2460 is a
medium-speed, very fine-grain color negative aerial film.
This film has a wide exposure latitude and is specifically
designed for processing to a color negative only. Since this
film does not have integral color masking, direct
interpretation can be made from the negative. Objects are
recorded in colors complementary to their natural colors.
The ESTAR Base provides flexibility, moisture
resistance, high tear resistance, and excellent dimensional
stability. KODAK AEROCOLOR IV Negative Film 2460 has
an abrasion-resistant emulsion, an antihalation undercoat,
and a dyed-gel backing.
The hardened emulsion permits high-temperature, rapid
processing in roller-transport processors, such as the
KODAK Aerial Color Processor, Model 1611, and the
KODAK EKTACHROME RT Processor, Model 1811, with
Quick-Change, using Process AN-6. This process consists
of selected KODAK EA-5 Chemicals and AN-6 Chemicals.
Processing can be easily tailored to optimize contrast for
specific applications.
This film is also compatible with Process C-41. It can be
processed in existing C-41 processors using either KODAK
FLEXICOLOR Developer or KODAK Developer
Replenisher, Process AN-6.
This film can be processed in rewind processing
equipment, such as the Morse M-10 developing outfit
(Military Designator: B-5), although this is not a primary
processing recommendation.
APPLICATIONS
KODAK AEROCOLOR IV Negative Film 2460 is for general
use in medium- to high-altitude aerial-mapping and
aerial-reconnaissance photography. It is suited for
geological, pollution, archeological, crop and forestry
studies; traffic control; city planning; railway, highway, and
hydraulic engineering; oceanography; and remote sensing,
as well as other areas where photogrammetry is used. It is
also well suited and recommended for use in digital film
recorders.
BASE
3.9-mil (0.10 mm) ESTAR Base with a gel backing.
TOTAL FILM THICKNESS
The nominal total thickness (unprocessed) of this film is
5.2 mils (0.132 mm). This includes emulsion—0.8 mil
(0.020 mm), base—3.9 mils (0.10 mm), and backing—
0.5 mil (0.013 mm).
WEIGHT
The weight of AEROCOLOR IV Negative Film 2460
(unprocessed), conditioned in equilibrium with 50 percent
relative humidity, is 0.04 lbs⁄sq ft (0.018 kg⁄sq ft).
SPECTRAL SENSITIVITY
This multilayer, color negative film is balanced for daylight
exposure.
SAFELIGHT
Total darkness is required.
EXPOSURE
Aerial Film Speeds (EAFS or ISO A equivalent) should not
be confused with conventional film speeds, which are
designed for roll and sheet films used in pictorial
photography. The characteristics of aerial scenes differ
markedly from those of ordinary pictorial or ground scenes
because of the smaller range in subject luminance,
atmospheric haze conditions, and other factors. Therefore,
different film-speed parameters are used to relate
aerial-scene characteristics to practical exposure
recommendations.
The KODAK Aerial Exposure Computer, KODAK
Publication AS-10, has been published based on the aerial
film speed criterion.
Nominal speed, daylight (no filter): EAFS or ISO A 125
(based on development for maximum contrast)
Note: The Aerial Film Speed given in this publication is
rounded to the nearest cube root of 2 step (equivalent to
1⁄3 stop).
Filters
This film incorporates an integral ultraviolet-absorbing
filter, so color correction filters are not normally used. If
necessary, additional color-balance adjustment in the blue
region can be achieved using KODAK Haze Cutting Filters
HF-4 or HF-5.
2 KODAK AEROCOLOR IV Negative Film 2460 • AS-2652
Typical Camera Exposure
A typical exposure for this film, in an aerial camera with a
2X antivignetting filter, is approximately 1⁄750 second at
f⁄5.6. This exposure is based on a solar altitude of 40
degrees, a clear day, and an aircraft altitude of 5000 feet.
Reciprocity Characteristics
No filter correction or exposure adjustment is required for
exposure times from 1⁄10,000 second to 1⁄10 second.
IMAGE STRUCTURE
*
Granularity values read at a net green diffuse density of 1.0 with a
48-micrometre aperture.
STORAGE
For consistent results, all aerial films should be stored
under fairly constant conditions. Kodak aerial films are
“usually” packaged in equilibrium with 40 to 50 percent
relative humidity. High temperatures or high humidity may
produce undesirable changes in the film. Color films are
more seriously affected by adverse storage conditions than
are black-and-white films. These adverse conditions affect
the three emulsion layers to different degrees, thus causing
changes in the color balance, as well as possible changes in
overall film speed and contrast.
Unexposed Film
While this film has exceptionally good rawstock keeping
characteristics at room temperature, it is recommended
that film that will not be exposed within two weeks be
stored in a refrigerator at 55° F (13° C) or lower, or freezer
at 0 to -10° F (-18 to -23° C), in the original sealed
container. If the film is stored in a refrigerator, remove it
about 2 hours before opening; if stored in a freezer, remove
it about 8 hours before opening. A sufficient warm-up time
is necessary to prevent moisture condensation on cold
film—otherwise, moisture spotting, ferrotyping, or sticking
may occur.
Exposed Film
Although this film has excellent latent-keeping properties,
it remains prudent to keep exposed film cool and dry
whenever practical. Process the film as soon as possible
after exposure to avoid undesirable changes in the latent
image. If it is necessary to hold exposed but unprocessed
film for more than a week, it should be resealed and
refrigerated at 40° F (4° C) or lower. Before unsealing and
processing exposed film that has been held in cold storage,
follow the warm-up procedures described above for
unexposed film.
Process rms Granularity
*
C-41, 3:15 dev time 8.5
C-41, 4:15 dev time 13
C-41, 5:15 dev time 15.5
Processed Film
For best keeping, store processed film in a dark, dust-free
area at 50 to 70° F (10 to 21° C) and 30 to 50 percent
relative humidity. Preferably, store negatives on the spool
or in individual KODAK Sleeves. High relative humidity
promotes the growth of mold and causes ferrotyping. Very
low relative humidity causes excessive curl and brittleness.
Avoid storage temperatures over 80° F (27° C).
Caution! Do not freeze processed AEROCOLOR IV
Color Negative Film 2460. Freezing processed film can
cause coupler alterations.
PROCESSING
The primary recommendation for processing 2460 Film is
in Process AN-6 using mechanized processors.
Mechanized processing in roller-transport processors
offers the advantages of uniform treatment of all portions
of the roll, freedom from banding, and absence of
significant density variations from ends of the roll to the
center.
Note: Contrast may be easily tailored over a range of
approximately 0.65 to 0.95 gamma to suit various
acquisition and personal preferences. The following tables
for Process AN-6 pertain to the highest contrast option; a
table at the end of this section lists both AN-6 and C-41
developer time/temperature options to achieve a variety
of desired contrasts.
Process AN-6 Cycle Times
In each case, the film is fed emulsion side down into the
processor.
This publication provides general information regarding
the KODAK Aerial Color Processor, Model 1611, and the
KODAK EKTACHROME RT Processor, Model 1811. Refer
to the operating manuals for additional set-up information.
Note: For a list of firms equipped to offer machine
processing of 2460 Film, send an e-mail to
aerial@kodak.com or write to Eastman Kodak Company,
Aerial Imaging, Rochester, New York 14653-7128.
Processor
Trans p o r t Sp e e d
(feet per minute)
Dry-to-Dry
Processing
Time
KODAK Aerial Color
Processor, Model 1611
4.2 11.8 minutes
KODAK EKTACHROME RT
Processor, Model 1811 (with
Quick-Change)
4.2 11.6 minutes
KODAK AEROCOLOR IV Negative Film 2460 • AS-2652 3
Chemicals
Process AN-6 uses the following KODAK EA-5 and AN-6
Chemicals:
KODAK Developer Starter, Process AN-6
KODAK Developer Replenisher, Process AN-6
KODAK EA-5 First and Second Stop Bath and
Replenisher
KODAK EA-5 Bleach and Replenisher
KODAK Aerial Color Fixer and Replenisher
KODAK EA-5 Stabilizer and Replenisher
Optional: KODAK FLEXICOLOR Final Rinse and
Replenisher can be used to reduce water spots and
drying marks
Notice: Observe precautionary information on product labels and
Material Safety Data sheets.
Processing Sequence (4.2 fpm):
KODAK Aerial Color Processor, Model 1611
KODAK EKTACHROME RT Processor, Model 1811,
Quick-Change
*
Set air-damper control knobs at 8. The dryer temperature may require
adjustment depending on the ambient temperature and humidity conditions
in the processing area.
Solution/Step Tank No.
Time
(seconds)
Temperature
° F ° C
AN-6 Developer 1, 2, 3 179.3 106 ± 0.5 41.1 ± 0.3
Skip Tanks 4 - 9 28.4 — —
Stop Bath 10 58.9 120 ± 549 ± 3
Wash 11 58.9 120 ± 549 ± 3
Bleach 12 58.9 120 ± 549 ± 3
Fixer 13 58.9 115 ± 546 ± 3
Final Wash 14, 15, 16 176.0 120 ± 549 ± 3
Dryer — 88.7 145 ± 563 ± 3
Solution/Step Tank No.
Time
(seconds)
Temperature
° F ° C
Skip Tanks 1, 2, 3 18.1 — —
AN-6 Developer 4, 5, 6 175.9 106 ± 0.5 41.1 ± 0.3
Skip Tanks 7 - 12 29.2 — —
Second Stop 13 58.6 120 ± 549 ± 3
Wash 14 58.6 120 ± 549 ± 3
Bleach 15 58.6 120 ± 549 ± 3
Fixer 16 58.6 115 ± 546 ± 3
Final Wash 17, 18 117.3 120 ± 549 ± 3
Dryer
*
—122.1140 ± 560 ± 3
Replenishment and Wash Rates (4.2 fpm):
Note: These rates have been rounded to the nearest usable
increment.
Models 1611 and 1811 with Quick Change
*
The required rates will vary with the average exposure level. Make an
adjustment if the control strip density levels increase or decrease
substantially.
Bleach Regeneration
Regeneration of used EA-5 Bleach will reduce processing
solution costs and substantially reduce the amount of
bleach discarded to the sewer. Collection and treatment
tanks for bleach overflow solution and chemical testing
capability are required. A detailed laboratory procedure is
available from Eastman Kodak Company.
C-41 Processing
This film may be processed in KODAK FLEXICOLOR
Chemicals for Process C-41. To achieve results like Process
AN-6, extend the development time to 5’15” at 100° F
(38° C) with a basic replenishment rate of 94 mL⁄ft
2
.
Shorter development times may be used to achieve lower
contrast, if desired. Substitute AN-6 Developer using a
developer time of 2’56” at 106° F (41° C) for increased
productivity.
Note: Do not use KODAK FLEXICOLOR Developer LORR,
as the low tank turnover would be insufficient to maintain
proper chemical equilibrium and sensitometric control.
Solution/Step
Basic
Rate (mL/
ft
2
)
Film Width
70 mm
(mL/min)
5-in. (mL/
min)
9 1/2-in.
(mL/min)
AN-6
Developer
*
110 105 195 365
Stop Bath 200 195 350 665
Wash — 2 gal/min —
Bleach 90 90 160 300
Fixer 100 100 175 335
Final Wash — 2 gal/min —
4 KODAK AEROCOLOR IV Negative Film 2460 • AS-2652
C-41 Processing Cycle
*
If you increase the bleach and fixer times to 6:30 or longer, you can extend the
temperature range to 75 to 105° F (24 to 41° C).
†
In some processors, a lower wash-water temperature may affect solution
temperatures in adjacent tanks. Longer warm-up times may be needed. If it
affects developer temperature during processing, you may need to use a
higher wash-water temperature.
‡
Rates are for first wash and a two-stage countercurrent final wash. Double
these rates for a single-stage final wash.
§
Use a two-stage (two-tank) countercurrent fixer, preferably with the same
time in each tank. Agitation and filtration in each tank are required. If your
processor has a single fixer tank, using in-line electrolytic desilvering will
decrease the safety factor for adequate fixing.
If your squeegees are efficient enough to maintain a low fixer carryover, you
can reduce the wash time to 2:10.
**
Optional: KODAK FLEXICOLOR Final Rinse and Replenisher can be used to
reduce water spots and drying marks.
For additional information using Process C-41, see
KODAK Publication Z-131, Process C-41 using KODAK
FLEXICOLOR Chemicals.
Development Options to Achieve Various Contrasts
Adjust developer time/temperature per the table below to
achieve a variety of contrasts. When changing processor
transport speeds, be sure to adjust replenishment flow
rates accordingly, to maintain desired basic replenishment
rates.
*
Film must be completely immersed in developer. Includes immersion time
and transfer time to the next tank. Keep transfer time to 20 seconds or less.
Note: Based on a 3-tank developer system in a Model 1611
or 1811 Processor, 2:56 = 4.2 fpm and 2:17 = 5.4 fpm.
FLEXICOLOR
Chemical
Time
min:sec
(sec)
Te m p
° C (° F)
Basic Repl
Rate (mL/ft
2
)
Developer
3:15 to 5:15
(195 to 315)
38 ± 0.3
(100 ± 0.5)
*
94
Bleach III
3:00 to 6:00
(180 to 360)
38 ± 3
(100 ± 5)
*
95
Wash
1:05
(65)
24 to 41
(75 to 105)
†
2900
‡
Fixer
§
4:20
(260)
38 ± 3
(100 ± 5)
95
Wash
3:15
(195)
24 to 41
(75 to 105)
2900
‡
Wash
**
1:05
(65)
24 to 41
(75 to 105)
95
Dry As needed
Not over
60 (140)
Developer
Ty p e
Push
Value
Time
min:sec
(sec)
*
Te m p
° C (° F)
Approx.
Contrast
ISO A
Equivalent
AN-6 0 2:17 (137) 38.9 (102) 0.63 80
AN-6 1 2:17 (137) 40 (104) 0.70 90
AN-6 2 2:17 (137) 41 (106) 0.78 100
AN-6 3 2:56 (176) 40 (104) 0.84 110
AN-6 4 2:56 (176) 41 (106) 0.90 125
C-41 0 3:15 (195) 38 (100) 0.63 80
C-41 1 3:45 (255) 38 (100) 0.70 90
C-41 2 4:15 (270) 38 (100) 0.78 100
C-41 3 4:45 (285) 38 (100) 0.84 110
C-41 4 5:15 (315) 38 (100) 0.90 125
REWIND PROCESSING
Note: This is not a primary recommendation.
KODAK AEROCOLOR IV Negative Film 2460 yields
optimum results with modern, high-temperature,
continuous-processing machines. It can be processed in
rewind equipment, although this method is not a primary
processing recommendation. Eastman Kodak Company no
longer offers packaged chemicals for such processing.
Customers wishing to use rewind equipment such as the
Gordon/Morse M-10 Developing Outfit (Military
Designator: B-5) may contact Aerial Imaging for
information on exposure, processing chemicals, process
cycles, and general recommendations.
PROCESS CONTROL
KODAK Control Strips, Process AN-6, are available and are
recommended for monitoring the processing of
AEROCOLOR IV Film in roller-transport processors. For
detailed information on process control and
troubleshooting, refer to KODAK Publication Z-200, Using
Processes AR-5, AN-5, and AN-6 for KODAK Color Aerial
Films.
PRINTING NEGATIVES
You can reproduce images made on AEROCOLOR IV
Negative Film by using a variety of Kodak materials.
Color Transparencies
You can make transparencies directly (or by first scanning)
on KODAK PROFESSIONAL ENDURA Clear Display
Material.
Color Prints
You can make prints directly (or by first scanning) on—
KODAK PROFESSIONAL SUPRA ENDURA VC Digital
and ULTRA ENDURA Papers
KODAK PROFESSIONAL ENDURA Transparency
Display Material
KODAK PROFESSIONAL ENDURA Metallic VC Digital
Paper
KODAK AEROCOLOR IV Negative Film 2460 • AS-2652 5
DIMENSIONAL STABILITY
The dimensional stability of aerial films is of particular
interest and importance in accurate mapping and in the
reproduction of maps.
Dimensional stability is an all-inclusive term. In
photography, it applies to size changes caused by changes
in humidity and in temperature, and by processing and
aging. The absence of solvent in ESTAR Base is one of the
reasons why ESTAR Base films show excellent dimensional
stability. The dimensional properties of ESTAR Base may
vary slightly in different directions within a sheet; the
differences that may exist, however, are not always
between the length and width directions.
Temporary Dimensional Changes
Permanent Dimensional Changes
SIZE DATA AND ORDERING INFORMATION
Information on available sizes and minimum order
quantities of this film is available on the web at
www.kodak.com/go/aerial. You can also write or contact:
Aerial Imaging
Eastman Kodak Company
343 State Street
Rochester, New York 14650-0505
aerial@kodak.com
Note: The Kodak materials described in this publication
used with AEROCOLOR III Film are available from those
dealers normally supplying Kodak products. Other
materials may be used, but equivalent results may not be
obtained.
Thermal Coefficient of Linear Expansion:
0.001% per degree F of change
0.0018% per degree C of change
Humidity Coefficient of Linear Expansion (Unprocessed):
0.0025% per 1% change in relative humidity
Processing Dimensional Change:
-0.02% to +0.01% shrinkage to swell
Aging Shrinkage of Processed Film:
0.06% 1 week at 120° F (49° C), 20% RH
0.03% 1 year at 78° F (25.5° C), 60% RH
CURVES
Modulation Transfer Function
Spectral Sensitivity
Process: AN-6
Densitometry: Status M
1001 2 3 4 5 10 20 50 200 600
SPATIAL FREQUENCY (cycles/mm)
RESPONSE (%)
10
1
2
5
3
7
30
20
100
70
50
200
R
G
B
Effective Exposure: 1/25 Second
Densitometry: Status M
Density: 0.3>D-min
700 750650600550500450400350300250
*Sensitivity = reciprocal of exposure (erg/cm ) required
to produce specified density
WAVELENGTH (nm)
2
LOG SENSITIVITY
0.0
*
1.0
2.0
3.0
4.0
Yellow-
Forming
Layer
Magenta-
Forming
Layer
Cyan-
Forming
Layer
TI2652C
KODAK AEROCOLOR IV Negative Film 2460
Aerial and Industrial Markets
EASTMAN KODAK COMPANY • ROCHESTER, NY 14650-0505
New 10-09
KODAK AEROCOLOR IV Negative Film 2460
KODAK Publication No. AS-2652
NOTICE: While the sensitometric data in this publication are typical of production coatings, they do not
represent standards which must be met by Kodak. Varying storage, exposure, and processing conditions will
affect results. The company reserves the right to change and improve product characteristics at any time.
Spectral Dye Density
Characteristic Curve, Developed for Low Contrast
D-min
Mid-Scale Neutral
and D-min.
Typical densities for a midscale neutral subject
750700
2.5
1.5
2.0
0.5
1.0
DIFFUSE SPECTRAL DENSITY
600 650
WAVELENGTH (nm)
400 450
0.0
500 550
Process: C-41, 3'15" dev time (or Process AN-6,
137 seconds, 38.9 C)
Exposure: Daylight
Densitometry: Status M
LOG EXPOSURE (lux-seconds)
-3.0-4.0
0.0
-2.0
DENSITY
1.0
2.0
3.0
4.0
-1.0 0.0
B
G
R
1.0
Characteristic Curve, Developed for Medium Contrast
Characteristic Curve, Developed for Maximum Contrast
Process: C:41, 4’15” dev time
(or Process AN-6, 137 seconds, 41 C)
Exposure: Daylight
Densitometry: Status M
LOG EXPOSURE (lux-seconds)
-3.0-4.0
0.0
-2.0
DENSITY
1.0
2.0
3.0
4.0
-1.0 0.0
B
G
R
1.0
Process: C-41, 5'15" dev time
(or Process AN-6, 176 second. 41 C)
Exposure: Daylight
Densitometry: Status M
LOG EXPOSURE (lux-seconds)
-3.0-4.0
0.0
-2.0
DENSITY
1.0
2.0
3.0
4.0
-1.0 0.0
B
G
R
1.0
Kodak, Kodak Professional, Aerocolor, Duraclear, Estar, Ektacolor, Ektachrome,
Flexicolor, Gold, Panalure, Portra, Vericolor, and Wratten are trademarks.